The perfect gift to give a lover to remind them of what they had!!

If you're a guy, admit it. You've always wanted to have a replica of your own cock. To look at it up close, feel it, to give it a blowjob, maybe even to fuck yourself with it. Well, you can do all that by making a mold of your own manhood. That's what this kit advertises. The materials it uses are widely employed in the medical and film industries. So you can make a rubber replica of your penis, whether hard, soft, twisted, or whatever.

This kit comes with most of what you need to make two impressions of your penis. It includes powder, a 9-inch-long, 3.5 inch-wide tube to put your penis into, some silicone and catalyst (to be explained later), a thermometer, a strainer, spoons, and a black foam cap to put over the tube to anchor your willy in. For your part, you will need an erection that will last one and a half minutes, a mixing bowl, water, masking tape, an electric mixer (although I used a handheld immersion blender, which did the job nicely), some newspaper or towels, a scissors, and a watch or clock for timing.

Since this kit will make an exact replica of everything, be aware that any cock rings or piercings may need to be removed. You may also want to shave your pubic hair, because when you're done, you will have the impression compound sticking to bits of your crotch. You can pull the stuff off fairly easily, but it will be tedious. Those who oppose shaving for political reasons will have a chance to suffer for their convictions!

One thing to note: any dildo you make with this kit is meant for visual enjoyment only. That's because the materials used in it are not healthy for the mouth, vagina, or anus. If you do decide to stick it up any of your orifices, you will need to wear a condom. That's just a safety tip from the manufacturers.

Read the directions thoroughly. Read them two or three times. Do a practice run to make sure you get all the steps right. You only get enough plaster to make two dildos (although you can order more plaster from the company, just in case you can't keep your dick hard for over a minute). It's not easy to stay hard when you're caked in plaster, let me tell you.

The first time I did this, I had everything ready. I heated the water to 80 degrees, then mixed it in a bowl for about 30 seconds. Following that, I poured it into the cup, then sank my penis into it. It is important that you do whatever you need to do to keep an erection--unless you want to make a mold of a soft penis instead. That's why it may help to have another person help you with this, to prepare, mix, pour, and then bend over for you to look at while you're sticking your penis into the muck.

The whole process reminded me of getting fluoride treatment at the dentist's office. After a minute and a half (I did the job alone), the powder/water mix had hardened. It looked and felt like very firm tofu. It had tiny little bubble-holes in it, which is normal. As for me, I had bits of the hardened mix stuck to my pubes, the tip of my penis, and the underside of my furry balls. Unfortunately, my penis had been touching the side of the tube it was in, which of course left a hole in the mold. So, back to the drawing board for another try. This time I scaled the measurements of powder and water down and put them into a smaller container, so as to save powder.

My second try was successful. I could see that the hardened mixture had captured the intricate wrinkles and textures of my penis. After this, I moved on to making the cast. I mixed the catalyst and silicone, then poured it into the mold. (The directions tell you how to create a base for the dildo using masking tape.) You have to wait at least eight hours for the mix to harden. I'd recommend giving it a few extra hours. Once I'd waited long enough, I carefully peeled the cast out of the mold and voila! I was actually holding a perfect replica of my own dick! It was exact. Every contour was there. Even the spongy texture of my cock-tip was preserved there; and the feel was quite lifelike. It was amazing. At first, I hadn't quite believed the advertising on the package when it said things like "amazing detail," "perfect," and "realistic." Yet it really was a perfect likeness.

The color was brownish and the texture was rubbery, and of course the pink color of the tip of my cock could not be replicated. But the likeness was just amazing. I'm going to let it harden for another day, since it felt a little too soft, then start earnestly sucking on it. Now that I have my own cock to fuck and suck, I may never date or leave the house again, but that is the price we must pay for progress. Oh well.

All in all, I recommend this product. The only downside to it is that you need to use a condom while inserting it into you.